High pressure air blower
1.vacuum air pump IP55,insulation class F
2.Die cast aluminum
3.copper winding motor
4. warrant
Port: SHENZHEN
Minimum Order Quantity: 10 Set/Sets
Supply Ability: 1200 Set/Sets per Month
Payment Terms: T/T
Contact SupplierPackaging Detail: Hard carton with wooden pallets
Delivery Detail: 30 days
Rachel baker (ribake) high-pressure blower has the following performance:
High reliability
In addition to the impeller, high-pressure blower no other moving parts, and
impeller direct links to motor, no gear or transmission belt, so high
reliability, almost maintenance free.
Low Vibration
High precision machinery, return part of another piece of all through the
extreme precision balance design, testing, calibration so vibration rate is very
low.
Using range and service:
High-pressure blower is mainly used in gas transport system; Vacuum ascension
and clamping system; Packaging machine, Wastewater treatment plant ventilation;
Bag/bottled/filling system; Soil improvement; Foam molding system; Food
processing system; Laser printers; Dental vacuum suction machine; Paper handling
system; The loom, and so on.
High-pressure blower principle of work:
High-pressure blower is blowing and absorption of the vortex air pump, the fan
special blade design, it has high pressure, big air volume, low noise, high
temperature resistant etc. Characteristics. Pressure fan insulation performance
is strong, easy installation, high stability, the gas through without oil, dry,
of the highest quality. High pressure and high suction impeller unique design is
produced. Pressure of impeller with many edge fan blades, when the impeller
turns, because centrifugal effect, the two leaves of the air are quickly to rim
direction, turn the lose energy, wind pressure fast stack, they form the high
pressure or high force the speed be increased. When air is duct to import the
impeller, will again be accelerated. Because more than the fan blade pressure
turn energy, wind pressure fast stack, they form the high pressure or high
attraction. Drying machine high-pressure blower, Taiwan high-pressure blower
said the ring blower, has the air supply and air suction of two kinds of
function, the Siemens technology, through the gas without oil, dry, suitable for
many mechanical industry auxiliary equipment.
Maintenance and maintenance method:
1) high-pressure blower motor straight even impeller and belong to high speed
bearings need to add butter regular maintenance and prevent damage to the
(including the impeller's bearing).
2) the motor shaft power and pressure is
proportional to, to prevent long-term pressures lead to limit the shaft power
increase, motor load is overweight, often use is discharging valve, it is a
unloading valve, when the use of high-pressure blower pressure commentate
pressure valve set more than the pressure after, discharging valve will
automatically open, the excess stress release, protect a high-pressure blower
motor.
3) high-pressure blower internal institutions more closely, the impeller
and chassis clearance is small, so to filter debris and dust. It is to be in
commonly the intake loaded on fine mesh/filter. It according to different use
the site, often use different filtration precision filter.
4) in some special
occasions, it needs special protection: for example in sealed environment used,
should pay attention to ventilation cooling; When environment temperature (inlet
temperature is higher
Use points:
High-pressure blower operation, motor consumption in the current pressure and
vacuum degree with the increase of increase, such as current will lead trip, to
prevent tripping or save electricity, please increase the sectional area as far
as possible the outlet, or on inhaling or exhaust side wind pressure air volume
regulator device.
A. with-the entrance should air filter
1., air flow of the
total cross-sectional area should be more than one half of the fan export
sectional area.
2. As for the water send spirit, the depth of water pressure in
the catalog shall be indicated by the maximum static pressure value to below
70%.
3. To send spirit pressure, the temperature of the air friction exports
more than 10 °C at relationship is a normal, reason should be more than 1 M use
iron pipe.
B. air suction with-exit can add muffler The total sectional area
inhaled hole should be greater than blower entrance one half of sectional area.