Home  >  Tool Parts

BOSCH GWS 7-115 Carbon Brush for Power Tools - GWS 7-115

Carbon brush for power tools, 1.Long wear time carbon brush, 2.Firststage material carbon brush, 3.Best performance carbon brush - more info check here: http://www.buyindustrialtools.com/BOSCH-GWS-7-115-Carbon-Brush-for-Power-Tools-10111625/

Quick Brief

Place of Origin: Jiangsu China (Mainland) Brand Name: BOSCH Model Number: GWS 7-115 Type: Power Tool Parts material: M839 Graphite. size: 5*10*17mm

Product Features:

Carbon brush for power tools

1.Long wear time carbon brush

2.Firststage material carbon brush

3.Best performance carbon brush

Business Terms:

Port: Shanghai

Minimum Order Quantity: 1000 Pair/Pairs

Supply Ability: 1000000 Pair/Pairs per Month

Payment Terms: L/C,D/A,D/P,T/T

Contact Supplier
BOSCH GWS 7-115 Carbon Brush for Power Tools
Share to: Facebook Twitter LinkedIn Google+

Product Packagings & Delivery Terms:

Packaging Detail: Small plastic bags,Small box bags or according to u

Delivery Detail: Openings and received certificates after 30 days

Specifications and Product Details:

BOSCH GWS 7-115 Carbon Brush for Power Tools

1.From the appearance point of view:

This product chamfer decent, appropriate specifications, structure specifications

the wire cross-section and length, not loose, falling off, broken off side, off angle, clamp and so on.
2.From the use of terms:
(1) Carbon brush of high quality graphite, with long life and doesn't wear commutator or slip rings, commutator appears not to scratch, rough, ablation, drawing and so on.
(2) Has a good flow properties and set to change, so that spark suppression in the permitted range, and the energy loss is small.
(3)Carbon Brush runs, but heat, noise, not broken, do not change color brush braid, no ablation.
(4)Carbon brush is running,which can be on the surface of commutator or collector ring quickly- forming a uniform, moderate and stable oxide film.

we can supply various kinds of carbon brush for power tools,our carbon brushes have characters ,used such as long time,low spark.,

we also can supply carbon brush replacements, such as Hitachi series,Makita series,Bosch series,Dewalt series,Matao series,Black&Decker series.

Information for your reference

Carbon brush performance

Commutator:
Unit must be in good condition, with less than .002" out-of-roundness. Bar edge must be chamfered and there should be no burned edges.

Brush Holders:
They must be mechanically sound and permit the brush to slide freely. Brush holder fingers must move freely and if the unit consists of constant pressure springs, these springs must be in good condition. Springs that are difficult to move, have an excessive accumulation of carbon, or are worn, will cause excessive brush wear.

Brush Holder Angles:
The angles should be set to the original manufacturer's specification. Any more than a 2 degree variation in the setting can cause arcing, bar burning, and excessive wear. Brush holders that vary in the angle set to the commutator will cause the unit to be "off neutral".

Brush Holder Spring Tension:
Maintaining the proper spring pressure reduces arcing, brush wear, heating, and commutator wear. Light spring tension can cause threading and definitely will shorten the brush life. As a general rule, we recommend that the brushes be set at 4 psi pressure. To calculate the pressure, measure the width and thickness of the contact face and calculate as follows:

Pressure in Pounds/Brush = (Width x Thickness x 4 psi)

Brush Holder Quartering:
To insure that the best machine electrical neutral can be achieved, the brush holders must be quartered. Quartering is setting the brush holders at equal distance around the commutator. For a 4 pole machine, the spacing will be every 90 degrees. If the quartering is not properly set, you may experience excessive arcing, heating, brush wear, and commutator wear.

Machine Neutral:
To obtain optimum machine performance, the brush must be set at the machine electrical neutral. If the unit is off neutral, you may observe sparking under a no-load condition. Depending upon how far off neutral the machine is set, there may be arcing and bar burning.

Carbon Brushes Description

The Principal Dimensions of a Carbon Brush

Note:

We work to NEMA and ANSI tolerances on the dimensions given to us. Width and thickness dimensions should be established accurately. If in doubt, it should be noted that the internal dimensions of the brush holder should be about .003" greater than the nominal dimensions of the brush.

Flexible length is the length from the top of the longest side of the brush to the center of the terminal hole.

The dimensions of "d" on the double shank terminals may vary with the flexible size, reducing as the flexible size increases and the minimum permissible dimension should be stated.

Terminals:
Please give the size of opening.

BOSCH GWS 7-115 Carbon Brush for Power Tools suppliers    BOSCH GWS 7-115 Carbon Brush for Power Tools manufacturers